Product Description
1.General Introduction
The multifunctional self-resetting dual display protector integrates over-voltage protection, under-voltage protection, over-current protection and integrated intelligent protector. When there is over-voltage, under-voltage and over-current solid barriers in the line, this product can instantly cut off the circuit, avoiding unnecessary damage to electrical equipment. When the circuit returns to normal, the protector can automatically restore the circuit to make the electrical equipment work normally. The overvoltage value, undervoltage value, overcurrent value, circuit recovery time value and overcurrent protection reset time value of this product can be set by themselves. Adjust the corresponding parameters according to local actual conditions and electrical usage conditions.
2. Product features
2.1 The product fully conforms to the single-phase self-reclosing recloser produced by the enterprise standard.
2.2 When the line has overvoltage, undervoltage and overcurrent faults, the product will automatically cut off the line. When the line voltage or current returns to normal, the product will automatically resume normal power supply after the delay time set by the user.
No, manual operation is required.
2.3 When the line appears instantaneous or transient overvoltage, the protector does not malfunction.
2.4 The line voltage is unstable or the power is suddenly cut off due to some factors, when the power recovers, the product will not connect to the power immediately. This delay time is set by the user according to the local situation.
2.5 The line voltage should not be higher than 330vac to prevent the product itself from being damaged due to excessive voltage. Please contact the manufacturer if a high power supply is required in a specific situation.
3. Normal usage conditions
3.1 The ambient temperature does not exceed +50 degrees and not less than -10 degrees.
3.2 The altitude of the installation site does not exceed 2000 meters
3. 3 Humidity: not more than 60%
3.4 Pollution degree 3
4. Installation conditions
4. 1 The protector can be installed vertically or horizontally in the cabinet, and special orders are required for special occasions.
4.2 It should be installed in a non-explosive medium, and there is no sufficient fermented bean curd metal and insulating gas and conductive dust in the medium.
4.3 It should be installed in a place where there is no rain or snow.
5. Main technical parameters
| Rated voltage |
220VAC 50Hz |
| Rated current |
1A-63A adjustable (default 40A) |
| Overvoltage action cut-off value |
240V-300VAC can be set (default 270VAC) |
| Overvoltage action cut-off value |
140V-200VAC can be set (default 1 70VAC) |
| Overcurrent action cut-off value |
63A: 1A-63A can be set (default 40A) / 40A: 1 A-40A can be set (default 40A) |
| Transmission delay time after power-on and power-off |
5-300S adjustable (default 5S) |
| Boot delay time |
1-300S adjustable (default 5S) |
| Reset delay time after overcurrent protection |
30-300s adjustable (default 30s) |
| Product overcurrent delay time |
6s (overcurrent time greater than this time will be confirmed as overcurrent and provide protection) |
| Own power consumption |
less than or equal to 2W |
| Electrical machinery life |
greater than or equal to 100,000 times |
6. Product settings
Note: If the keyboard is longer than 60 seconds at any position before saving, the operating system will abandon all settings and restart.
7. Use
After the protector is installed, the user can wire it, and select the wire section that meets the standard
according to the setting current of the protector. Note that the input and output wires of the protector
cannot be connected incorrectly to avoid damage to the product or power failure.
8. Precautions
8. 1 When performing various current operation or tests, users should follow the relevant regulations and
pay attention to the following matters to ensure the correct and safe use of this product.
8.2 According to the product standard, the input and output terminals are connected correctly (the load
current should be less than the protection current value of the product)
8.3 The neutral wire N cannot be connected wrongly and must be connected reliably, otherwise the
protector cannot work normally.
8. 4 Before turning on the power, carefully check whether the wiring is correct, whether the load size
matches the current protection value of the product, and whether the wiring screws are tightened,
otherwise the product will be damaged.
8.5 After the product is connected to the power supply, please do not touch the live parts to avoid electric
shock.
8.6 This product needs to cooperate with micro-break to play a short-circuit protection function, otherwise
the product will not be able to provide protection when a short-circuit occurs in the load of the product.
8.7 Since the product has an automatic reset function, after the product is protected and activated, the
load (electrical appliances) should be removed immediately, and the circuit should be checked, otherwise
the product will frequently switch on the load and disconnect the load, which will eventually damage the
product or electrical appliances due to frequent overloads for a long time.
8.8 The product should be protected from moisture and dust when it is not used for a long time. The
product should be tested as described above before using, and it can be used while it is normal.
8.9 This product has no isolation function. Please disconnect the front-level circuit breaker switch when
repairing the circuit.
8. 10 The zero line (N line) of this product is directly connected and has no disconnection function.
8. 11 This product has no over-current short-circuit breaking capacity. Please install a small circuit
breaker such as DZ-47 or C65 at the front of the line as over-current protection.
8.12 If the actual setting is different from this manual due to product upgrade, please contact our
company. Product upgrade will not be notified separately.
Company Profile
Zhejiang Zhiyi Electric Co.,Ltd(ZOII) build in 2012 The company is a high-standard manufacturer specializing in the development and production of Solar Power system accessories ,The wide range products under manufacturing covers such as AC&DC Surge Protective Device(SPD), AC&DC Miniature Circuit Breaker(MCB),AC&DC Moulded Case Circuit Breaker(MCCB),Voltage & Current Protector,DC FUSE,MC4 PV connector ,combiner box etc. The company has passed ISO9001 and products all certified by TUV, CE, CCC, etc.
Our product quality is steady and price competitive, because of that every Part of our products is produced by ourselves. Our company accepts OEM&ODM customers, we are good at promoting cooperation and putting customers first. We are providing the dedicated service to customers according to our rich experience. Willing to go forward hand in hand with you!
Packaging & Shipping
Certifications
FAQ
1. who are we?
We are based in Zhejiang, China, start from 2012,sell to Mid East(30.00%),Africa(25.00%),Eastern Asia(10.00%),South Asia(10.00%),South America(10.00%),Eastern Europe(10.00%),North America(5.00%). There are total about 51-100 people in our office.
2. how can we guarantee quality?
Always a pre-production sample before mass production;
Always final Inspection before shipment;
3.what can you buy from us?
AC & DC Surge Protective Device,Voltage & Current Protector,AC& DC MCCB,Universal circuit breaker,DC Fuse Holder
4. why should you buy from us not from other suppliers?
Zhejiang Zhiyi Electric Co.,Ltd(ZOII) build in 2012 ,We have more than 10 year experience development and production of Solar Power system accessories ,such as DC SPD,DC MCB,DC MCCB,DC FUSE,Universal circuit breaker,and so on.
5. what services can we provide?
Accepted Delivery Terms: FOB,CFR,CIF,EXW;
Accepted Payment Currency:USD,EUR,CNY;
Accepted Payment Type: T/T,L/C,D/P D/A,MoneyGram,Credit Card,PayPal,Western Union,Cash;
Language Spoken:English,Chinese,Spanish
){kind=link}
){kind=link}